Adhesive Solutions for Industrial Dust Collection Filters
In industrial dust‑collection systems, the sealing, bonding, and repair of filter cartridges, filter bags, sintered plates, and dust‑removal equipment impose specific requirements on adhesives, demanding a balance of high‑temperature resistance, corrosion resistance, strong adhesion, and environmental compatibility.
The following are adhesive solutions and selection recommendations for various applications:
1. Adhesive Solution Specifically for Filter Cartridges 
Sealing by adhesive bonding between the filter media and the end cap
Recommended adhesive type : Polyurethane potting compound or epoxy potting compound
Polyurethane properties (for ambient‑temperature filter cartridges):
It requires rapid curing, with a 30-minute cure time allowing for demolding and turnover, and is suitable for assembly-line operations.
Wide temperature resistance range (-40°C to 80°C), excellent resistance to impact and vibration, and strong adhesion to metal end caps, ensuring it does not easily come loose.
Epoxy resin properties (for high-temperature filter cartridges):
A high-temperature-resistant epoxy potting compound, capable of withstanding temperatures up to 250°C.
2. Adhesive Solution for Dust-Removal Filter Bags
Zero-emission glue application at suture needle eyelets
Recommended adhesive type: Silicone sealant
Features: Fast curing—8 seconds to 3 minutes—extremely rapid cure, with long-term resistance to temperatures up to 280°C.
3. Adhesive Solutions for Sintered Plate Dust Collectors 
Sintered‑plate dust collectors are filtration devices that use sintered metal plates as the filtering element. These collectors employ a sintering process: metal powders or fibers are melted at high temperatures and then cooled to solidify, forming porous filter plates. The pores allow gases to pass through smoothly while effectively trapping and capturing solid particulates in the gas stream, thereby achieving air purification. With notable advantages such as high filtration efficiency, long service life, and low operating costs, sintered‑plate dust collectors have found widespread application across industries including steel, cement, chemicals, and power generation.
Adhesive application area: Sintered plate joint bonding and end-cap sealing bonding
Recommended adhesive type: Two-component epoxy structural adhesive, HNEP 6225-25, with a 5:2 mixing ratio, low cost, and strong bonding strength; Shanghai Hinnel HNEP6220-6 epoxy structural adhesive, offering high-temperature resistance, excellent toughness, and superior bonding performance.
4. Structural bonding of dust removal equipment
Metallic housing sealing
Recommended adhesive type : Silicone adhesive sealant
Features : Excellent elastic deformation capability, compensating for the thermal expansion and contraction of metals.
Wear-resistant liner bonding
Recommended adhesive type : Epoxy structural adhesive
Wear resistance : Resistant to dust erosion, with a service life extended by more than threefold.
IV. Key Selection Parameters
| Application scenarios | Adhesive requirements | Recommended Adhesive Type | Recommended Products |
| End-cap bonded ambient-temperature filter cartridge | Excellent adhesion to metal end caps, does not delaminate, and cures rapidly. | Polyurethane potting compound | HNPU556L Polyurethane Potting Compound |
| End-cap release model ambient-temperature filter cartridge | For ambient‑temperature filter cartridges, after potting and sealing, the end caps must be demolded. | Polyurethane potting compound | HNPU556LC Polyurethane Potting Compound |
| High-temperature-resistant filter cartridge | For potting of metal end caps on high-temperature-resistant filter cartridges. | Epoxy potting compound | HNEP6223D, capable of withstanding high temperatures up to 250°C. |
| Dust removal filter bag | Adhesive coating for suture needle eyes, resistant to 260°C and fast-curing. | RTV silicone rubber | HN702W/R, red, white, and beige—quick surface drying |
| Dust removal filter bag | Adhesive applied to suture needle holes; resistant to 280°C and cures rapidly. | Silicone sealant | HNSIL 8730G Two-Component 8-Second-Curing Silicone Sealant |
| Sintered Plate Dust Collector | Sintered plate joint bonding and end-cap sealing bonding | Epoxy structural adhesive | HNEP6225-25; HNEP6220-6 epoxy structural adhesive |
| Dust removal equipment | Sealed bonding of metal housings | RTV silicone rubber | HNSIL 736 Organic Silicone Adhesive Sealant |
| Dust removal equipment | Wear-resistant liner bonding | Epoxy structural adhesive | HNEP D120 Epoxy Structural Adhesive |
V. Industry Application Cases
Cement plant dust collector : The filter bag opening is sealed with silicone rubber, providing resistance to dust abrasion and alkaline gases.
Welding fume treatment : The filter cartridge uses conductive polyurethane adhesive to prevent static charge buildup.
Pharmaceutical industry : Water-based adhesives ensure that no extractables contaminate the product.
In the industrial dust‑removal sector, our meticulously developed adhesive solution for industrial dust‑filter cartridges has become an industry‑leading benchmark, thanks to its outstanding performance. This solution seamlessly integrates cutting‑edge materials science with a distinctive process‑design philosophy, achieving a perfect synergy between the filtration media and the adhesive through precisely formulated polymer composites. This innovative material combination not only significantly enhances the filter’s initial filtration efficiency but also delivers exceptional long‑term stability, effectively capturing particles larger than 0.3 microns and improving filtration accuracy by more than 40% compared with conventional approaches.
We are here to assist you at any time.
Whatever adhesive challenge you face, we are ready to offer our insights, expertise, and solutions to help you move forward.